224 products
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Regular price $62.95 USDScalerFab Welded Steel Replica Winch Front Bumper for Axial SCX10III Jeep CJ-7
Trail Bar & Stinger options available.
Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle while still allowing for a bumper-mounted winch.
The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.
Specifications:
- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and 8274 Winch, 3Racing Winch, and SSD Ox Power Winch mounting pattern)
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment
TO MOUNT WINCH: You will need to flip the winch mounting plate in order to install on bumper.
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.
3. Back screws with a washer and nut.
ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10III Jeep CJ-7 Trail Bar & Stinger options available.
*This bumper does NOT fit a winch. Click for Winch Bumper For CJ-7.
Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.
The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.
Specifications:
- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.
3. Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Regular price $57.95 USDScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10III Jeep CJ-7 Trail Bar & Stinger options available.
*This bumper does NOT fit a winch. Click for Winch Bumper For CJ-7.
Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.
The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.
Specifications:
- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.
3. Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Customer Reviews
Based on 2 reviews
100%
(2)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
Gives the truck a much better look with some more weight and winch mounting point.
J
Fit well, good finish, and it looks great.
Low-Profile Prerunner Series SCX10 III Base Camp Front Bumper
Regular price $73.95 USDScale looks abound in our latest release for the new Axial Adventure SCX10 III Base Camp Truck!
This Low-Profile Prerunner bumper was designed to fit slightly larger-than-stock tire applications. The width is even with the edges of the body.
Full-width Steel, welded Prerunner Series Front Bumper
for the SCX10 III Base Camp
Specifications:
- Made from 3/16" rod.
- Approx. 170mm wide.
- Mounts using included hardware. Spacer/additional washers may be necessary.
- Steel construction - Hand Made/Welded.
- Does not fit a winch.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:
-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,
-Flat Black: not as susceptible to chips
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Use washers (included) or spacer (not included) between steering link and frame rails. Use longer screws (included). Back screws with a washer and nut. Does not require use of SCX10 III body-post mounting system.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Customer Reviews
Based on 2 reviews
100%
(2)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
Great bumper
A
I'll be honest, ended up using this on my scx10.3 with an aftermarket proline body instead of the factory "Toyota" truck. Man does it look amazing! I went for shackle mounts and a front winch fairlead. The full set of front and rear bumpers plus rock sliders is absolutely beautiful. Haven't gotten a chance to run it yet, but they seem very strong, great quality welds.
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
Regular price $53.95 USDAxial Full-Width Steel, Welded Front Bumper for the Axial SCX10 III Base Camp.
Full width and full scale! This Class 1 worthy low-profile front bumper allows for full tire clearance under full turn & compressionIt even includes the ability to mount a winch behind the grill.
(MADE FOR STOCK VEHICLE- Any modifications may affect clearance)
Specifications:
-195mm wide, raised approx. 20mm above top of frame rails to close body gap.
- Predrilled with mounting holes to fit the RC4WD 9.5 CTI hole pattern. *Bumper is made to allow for a bumper-mounted winch behind the grill/body, not in front.
- Mounts using included hardware. Spacer/additional washers may be necessary.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:
-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,
-Flat Black: not as susceptible to chips
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Comp-Style Front Bumper for Axial Racing SCX10 III Base Camp
Regular price $58.95 USDOur most low-profile bumper with the best possible approach angle is here for the Axial Adventure SCX10III Base Camp!
RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper
Specifications:
- approx. 79mm wide (Just a bit wider than the frame rails)
- Raised approx. 20mm above the top corner of the frame rails to close body gap
- no fore/aft adjustment
- Bumper fits tight to the frame for the best possible approach angle.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:
-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,
-Flat Black: not as susceptible to chips
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Customer Reviews
Based on 2 reviews
100%
(2)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
T
Great rear bumper! Looks absolutely stunning on the basecamp. Only issue is the gap from the frame rails to the tabs. Once tightened down, it was fine.
M
Fit right on look amazing with the body I went with. Very happy with your product.
Prerunner Series SCX10 III Base Camp Front Bumper
Regular price $73.95 USDScale looks abound in our latest release for the new Axial Adventure SCX10 III Base Camp Truck!
The Prerunner series was designed for a combination of looks and performance under scale use. Made from 3/16" rod, the Prerunner Front Bumper for the SCX10 III Base Camp is a low-profile and scale trail armor option.
Full-width Steel, welded Prerunner Series Front Bumper
for the SCX10 III Base Camp
(MADE FOR STOCK VEHICLE- Any modifications may affect clearance. See our low-profile prerunner bumper HERE if running larger tires or adjusting shocks lower)
Specifications:
-Approx. 198mm wide. Wrapped ends match width/angle of body.
- Mounts using included hardware. Spacer/additional washers may be necessary.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:
-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,
-Flat Black: not as susceptible to chips
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Use washers (included) or spacer (not included) between steering link and frame rails. Use longer screws (included). Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Customer Reviews
Based on 2 reviews
50%
(1)
50%
(1)
0%
(0)
0%
(0)
0%
(0)
T
Perfect fit! Only issue was at full compression, the MTR’s would catch on the sides, some minor trimming and no more issue. Would highly recommend as it made the basecamp look awesome.
M
Great quality craftsmanship. Super stoked! Took a bit once ordered to finally ship but again, great craftsmanship.
Customer Reviews
Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
P
Love them! The fabrication on them is really great.
Put them to the test and did really well! Installation was kinda tricky, but definitely a great product. Very impressed.
Prerunner Series SCX10 III Bronco Front Bumper
Regular price $73.95 USDOur most popular series has made it to the SCX10 III Bronco!
The Prerunner series was designed for a combination of looks and performance under scale use. Made from 3/16" rod, the Prerunner Front Bumper for the SCX10 III Bronco is a low-profile, scale trail armor option.
Full-size Steel, welded Prerunner Series Front Bumper
for the SCX10 III Bronco
Specifications:
- Mounts using existing hardware
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use.
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Using included screws, mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below. *Use included washer between frame rails and body post mount as a spacer.
3. Back screws with a washer and nut.
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**
SEE HOW IT'S MADE:
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Customer Reviews
Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
Great fit and looks amazing
Narrow Winch Front Bumper for Axial Racing SCX10 III Bronco
Regular price $57.95 USD
ScalerFab Welded Steel Narrow Winch Front Bumper for Axial SCX10III Jeep Wrangler Bronco- Trail Bar & Stinger options available.
*This bumper is made for a bumper-mounted winch and includes pre-drilled holes with the RC4WD Warn Winch pattern. Click for Low-Profile Narrow Bumper without winch holes.
TO MOUNT WINCH: You will need to flip the winch mounting plate in order to install on bumper.
The ScalerFab SCX10 III bumpers are designed to work with the stock Axial body post mounting system. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.
Specifications:
- 115mm wide
- Includes mounting hardware (4 button-head screws, 4 nuts, & 6 washers)
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and 8274 Winch, 3Racing Winch, and SSD Ox Power Winch mounting pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s)
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
Mounting Instructions:
1. Bumper is made to slide inside the C-channel of the frame rails.
2. Using included screws, mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below. *Use included washer between frame rails and body post mount as a spacer.
3. Back screws with a washer and nut.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
Retro Series SCX10 III Bronco Front Bumper
Regular price $73.95 USDOur popular Retro Series is here for the Axial SCX10 III Bronco! This is the perfect mix of scale and throwback, with double tube work for that classic, old-school look! Pairs perfectly with the Retro Series Rear Bumper.
Full-size Steel, welded Retro Series Front Bumper for the Axial SCX10 III Bronco!
Specifications:
- 210mm wide
- Mounts using existing hardware
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.
**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:
-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own, or if you like a most rustic, patinaed look, as it will rust over time.
-Flat Black: not as susceptible to chips
-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available at Home Depot or Lowes.
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails.
2. Using included screws, mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below. *Use included washer between frame rails and body post mount as a spacer.
3. Back screws with a washer and nut.
For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.
Lifetime Warranty Info
ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc.
If you have an issue with your item, please leave detailed info below or you can mail in with info.
Items for warranty repair/replacement can should be mailed to:
ScalerFab, Inc
PO Box 130
Divide, CO 80814
Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)
