Specifications:

- approx. 79mm wide (Just a bit wider than the frame rails)
- Raised approx. 20mm above the top corner of the frame rails to close body gap
- no fore/aft adjustment
- Bumper fits tight to the frame for the best possible approach angle.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Back screws with a washer and nut.

 

ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10 III Jeep CJ-7 Trail Bar & Stinger options available. ** NEW OPTION - CLIPLESS BODY MOUNT BRACKET

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.

ScalerFab Welded Steel Rear Bumper for Axial SCX10 Honcho.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: not as susceptible to chips

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

Mounting instructions:
We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 115mm wide
- Requires trimming of plastic bumper for Pro-Line SR5 Body
- Laser-cut Gussets added for strength and added scale appearance
- Extra attention to detail during finishing process to optimize performance and appearance.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
-Gussets added for strength and added scale appearance
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

ScalerFab Steel Axial Racing SCX10III Adjustable, Bolt- On Double Bar Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommended hardware mounting kits available at the top of the page as an optional add-on.**

Protect your rig and look cool doing it! This is the brand new, just released ScalerFab Element RC Enduro Sendero Roll Bar. Simple, yet strong and full of SCALE! 

ScalerFab Axial Adventure SCX10 III Base Camp Roll Bar

Specifications:
-Hand-welded steel 3/16 rod
-Approx. 50mm tall x 185mm wide
-Angled slightly towards body to close body gap.
-Mounts by drilling 4 holes into truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.)

Specifications:
-190mm wide
-Bumper Top Plate sites approx. 20mm above the top of the frame rail.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-205mm wide
- Raised brackets specifically for XJ Body
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-190mm wide
- Will not fit a bumper-mounted winch (this rig is specifically built for a servo winch)
- Steel construction - Hand Made/Welded.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
***NOTE: Bumper brackets mount between frame and Front Body Post Receiver. - Body posts will need to be spread slightly to mount properly. Also, we recommend using a smaller body clip, as the stock ones will not completely clip due to bracket interference. Alternately, new holes could be drilled in the body posts perpendicular to the stock ones to allow the body clips to be pushed in from the front or back with no interference vs the side.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Main pic courtesty of #westernparccrawlers on IG! #ScalerFab for a feature!

ScalerFab Full-Width Welded Steel Rear Bumper for the Axial SCX10III Base Camp

Add a little scale to your RC! This classic style bumper offers a series of customized options. Add a license plate recess or hitch receiver for an ultra scale appearance.

 Specifications:

SCX10 II XJ Front Bumper mounting brackets. Sold in Pairs.

Specifications:
- 210mm wide
- Mounts using existing hardware
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own, or if you like a most rustic, patinaed look, as it will rust over time.

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available at Home Depot or Lowes.

For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 150mm wide
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-195mm wide, raised approx. 20mm above top of frame rails to close body gap.
- Predrilled with mounting holes to fit the RC4WD 9.5 CTI hole pattern. *Bumper is made to allow for a bumper-mounted winch behind the grill/body, not in front.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

Axial Adventure SCX10 III Jeep CJ-7    Low-Profile Comp Style Front Bumper  NEW RELEASE

Expertly crafted metal comp style front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Built with mild steel for a realistic scale appearance and unbeatable performance. Provides the highest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance while still protecting your rig.

- Approximately 70mm wide.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment.

Mounting Instructions:

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown.

3. Back screws with a washer and nut.

View of ScalerFab's Jeep CJ-7 Clipless Body Mount Bracket

This Axial Adventure SCX10 PRO Front Bumper with Gussets (Pro series gussets for added strangth) is the perfect addition for your SCX10 Pro chassis. Made of sturdy metal, this bumper is designed for long lasting performance, allowing you to customize your adventure bumper with optional add-ons!

Specifications:

- 115mm wide with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. **Pics depict regular scx10 bumpers. The pro WILL HAVE STRAIGHT slots for mount to the new PRO chassis.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:

- approx. 150mm wide
- Requires trimming of plastic bumper for Pro-Line SR5 Body
- Bumper Top Plate sites approx. 20mm above the top of the frame rail.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- Requires trimming of plastic bumper for Pro-Line SR5 Body
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Includes Pre-drilled mounting holes for winch(RC4WD WARN 9.5cti and 8274 Winch, 3Racing Winch, and SSD Ox Power Winch mounting pattern)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab's Builder Brackets take the guesswork out of fabbing your own bumpers. The SCX10 III Brackets/Adapter fit inside the c-channel frame rails. They do not mount to the outside of the frame rails like some of our other brackets. They come in a set of 2 and price includes FREE US SHIPPING. These sit about 17mm above the end of the frame rails, made to close the body gap on the Axial Adventure SCX10 III Base Camp. 

Non-Raised option can be found HERE.

Specifications:
-Laser cut out of 10ga mild steel
-Raised approx. 17mm
-Sticks out approx. 35mm from end of frame rails
-Predrilled mounting holes & adapter holes. 

ScalerFab's Builder Brackets take the guesswork out of fabbing your own bumpers. The SCX10 III Brackets/Adapter fit inside the c-channel frame rails. They do not mount to the outside of the frame rails like some of our other brackets. They come in a set of 2 and price includes FREE US SHIPPING. These sit about 2.5mm above the end of the frame rails, made to close the body gap on the Axial Adventure SCX10 III JLU, Gladiator, and Bronco. 

Raised option can be found HERE.

Specifications:
-Laser cut out of 10ga mild steel
-Raised approx. 2.5mm
-Sticks out approx. 48mm from end of frame rails
-Predrilled mounting holes & adapter holes. 

Choose your own adventure with the ScalerFab Comp-style front bumper for Axial Adventure SCX10 Pro 4WD Chassis. Built with carbon steel, this bumper will let you trail with confidence. Customize with our optional add-ons for your specific body.

Specifications:

- Approx. 82mm wide bumper with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. 
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

This Axial Adventure SCX10 PRO Front Bumper is the perfect addition for your SCX10 Pro chassis. Made of sturdy metal, this bumper is designed for long lasting performance, allowing you to customize your adventure bumper with optional add-ons!

Specifications:

- 115mm wide bumper with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. **Pics depict regular scx10 bumpers. The pro WILL HAVE STRAIGHT slots for mount to the new PRO chassis.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.