Protect your rig and look cool doing it! This is the brand new, just released ScalerFab Element RC Enduro Sendero Roll Bar. Simple, yet strong and full of SCALE! 

ScalerFab Element RC Enduro Sendero Roll Bar

Specifications:
-Hand-welded steel 3/16 rod
-Approx. 80mm tall x 170mm wide
-Mounts by drilling 4 holes into truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.)

Fits the following bodies, and may fit others (bumper sits even with top of frame rails and offers some fore/aft adjustment):

-Enduro Sendero/Sendero HD
-Enduro Trailwalker
-Pro-Line Racing 46 Power Wagon

Push all the way in for an ultra low-profile bull-bar look, or adjust out to fit a bumper mounted winch! (does not come pre-drilled with bumper mounting holes)

ScalerFab's RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper for Element RC Enduro Sendero/Trailwalker

Specifications:

- 74mm wide
- 20mm deep top plate w/ some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: https://amzn.to/3kBHM81

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Element RC Enduro Sendero/Sendero HD Cab-Only Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) This set is specifically for only using the cab portion of the Enduro Sendero. Will be shorter in the rear than our regular Sendero Rock Sliders to only cover the length of the cab.
Our Sliders take the place of the stock plastic skid plates.The receiver box and ESC will either need to be relocated or attached to our skid plates option with double-sided tape, which we highly recommend.

ALL NEW Body Capture Bar Option available! Our Body Capture Bar supports the lexan body for full protection to help keep the body from caving in or tearing!

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Element RC Enduro Sendero/Trailwalker Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) take the place of the stock plastic skid plates.
The receiver box and ESC will either need to be relocated or attached to our skid plates option, which we highly recommend.

ALL NEW Body Capture Bar Option available! Our Body Capture Bar supports the lexan body for full protection to help keep the body from caving in or tearing! (All pictures depict this option- a solid rod behind the main Rock Slider Bar with enough space for the body to fit between the two)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 207mm wide
- Mounts using existing holes in frame. Does not mount like stock plastic bumper(s) - Longer Hardware recommended (hardware not included)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 200mm wide
- Will not fit a bumper-mounted winch (this rig is specifically built for a servo winch)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-205mm wide
-Bumper is not made to fit a bumper-mounted winch. This model is built to give the best approach angle possible for this full-size option. Shown with optional front fairlead mount for servo winch.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.