Specifications:
- 193 to 200 mm wide (tapers from front to back)
-Fits in-between cutout on stock body.
If trimming body straight, measure the full width across and enter custom width. 
- Mounts using existing holes in frame. Does not mount like stock plastic bumper(s) - Longer Hardware recommended (hardware not included)
- Steel construction - Hand Made/Welded.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions:

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Specifications:
-195mm wide, raised approx. 20mm above top of frame rails to close body gap.
- Predrilled with mounting holes to fit the RC4WD 9.5 CTI hole pattern. *Bumper is made to allow for a bumper-mounted winch behind the grill/body, not in front.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

Specifications:
-192mm wide
-Bumper Top Plate sites approx. 20mm above the top of the frame rail.
**REQUIRES Trimming of body for fitment. Bumper is not made to fit a winch.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-190mm wide
-Bumper Top Plate sites approx. 20mm above the top of the frame rail.
**REQUIRES Trimming of body for fitment. Bumper is not made to fit a winch, but does have pre-drilled holes due to the laser cut top plate that is used. 
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-205mm wide
- Brackets specifically for TRX4
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: 

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Specifications:
-205mm wide
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Steel 90° Gussets (10-Pack)

gus·set
ˈɡəsət/
noun
noun: gusset; plural noun: gussets
Def: A bracket strengthening an angle of a structure.

*Laser-cut out of 16 gauge mild steel
*30mm x 19mm

ScalerFab Steel Axial Racing SCX10III Base Camp Adjustable, Bolt- On Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) slide right into the stock slot location of the plastic skid plate to replace the stock rock sliders.

(MADE FOR STOCK VEHICLE- Any modifications may affect clearance of front tires. Request custom length and specify measurement from front stock bolt location forward in order notes at checkout, if needed.)

Mounting Recommendations:
-Use 3rd hole on the brackets in stock mounting location

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use.

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own.

-Flat Black: matte black finish.

-Rustoleum Truck Bed Coating: OUT OF STOCK, no longer available.

ScalerFab Steel Axial Racing SCX10III Bronco Adjustable, Bolt- On Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

ALL NEW Body Capture Bar Option available! Our Body Capture Bar supports the lexan body for added protection to help keep the body from bending in or tearing!

Mounting Recommendations:
-Use 3rd hole on the brackets in stock mounting location

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: link text

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab Steel Axial Racing SCX10III Adjustable, Bolt- On Double Bar Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommended hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab Steel Adjustable, Bolt- On Rock Sliders Compatible with Axial Racing SCX10III Gladiator
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

Mounting Recommendations:
-Use first hole on front bracket, and second hole on rear bracket to match angled body of the SCX10 III Jeep Gladiator, just like the stock tapered rock sliders.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab Steel Axial Racing SCX10III Adjustable, Bolt- On Rock Sliders
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

Mounting Recommendations:
-Use first hole on front bracket, and second hole on rear bracket to match angled body of the SCX10 III Jeep Wrangler JLU, just like the stock tapered rock sliders.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab Steel Adjustable, Bolt- On Rock Sliders Compatible with Axial Racing SCX10III Gladiator
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures) mount directly to the stock location of the plastic skid plate to replace the stock rock sliders.

Mounting Recommendations:
-Use last hole, or adjust to desired offset.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Add scale points to your rig, not weight! These super light ScalerFab Aluminum Sand Ramps will get you over obstacles without weighing down you rig. Need I say more? 

Aluminum Sand Ramps

*Approximately 2" x 6"

Protect your rig and look cool doing it! This is the brand new, just released ScalerFab Element RC Enduro Sendero Roll Bar. Simple, yet strong and full of SCALE! 

ScalerFab Axial Adventure SCX10 III Base Camp Roll Bar

Specifications:
-Hand-welded steel 3/16 rod
-Approx. 50mm tall x 185mm wide
-Angled slightly towards body to close body gap.
-Mounts by drilling 4 holes into truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.)

ScalerFab's RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper for RC4WD C2X w/ Mohave Body.

Specifications:

- Approx. 82mm wide with 5mm raised brackets
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available at Home Depot or Lowes.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Fits the following bodies, and may fit others (bumper sits even with top of frame rails and offers some fore/aft adjustment):

-TRX D90
-Pro-Line Racing 46 Power Wagon

With multiple possible combinations to choose from on this bumper, you can truly build the perfect piece of trail armor for your needs. If you weren't a competitor already, our Comp-Style "bull-bar" Front Bumper will allow you to push the limits of your Ttraxxas TRX4 without having to worry about approach angles.

Drive OVER the rocks, don't work around your bumper!

Specifications:

- 79mm wide
- 20mm deep top plate w/ approx. some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Fits the following bodies, and may fit others (bumper sits even with top of frame rails and offers some fore/aft adjustment):

-#TRX4 Sport (Some modifications by grinding or cutting will be required to fit with the Sport Inner fenders.)
-Pro-Line 46 Power Wagon

With multiple possible combinations to choose from on this bumper, you can truly build the perfect piece of trail armor for your needs. If you weren't a competitor already, our Comp-Style "bull-bar" Front Bumper will allow you to push the limits of your #Traxxas TRX4 Sport without having to worry about approach angles.

Drive OVER the rocks, don't work around your bumper!

Specifications:

- 79mm wide
- 20mm deep top plate w/ approx. some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Fits the following bodies, and may fit others (bumper sits even with top of frame rails and offers some fore/aft adjustment):

-Enduro Sendero/Sendero HD
-Enduro Trailwalker
-Pro-Line Racing 46 Power Wagon

Push all the way in for an ultra low-profile bull-bar look, or adjust out to fit a bumper mounted winch! (does not come pre-drilled with bumper mounting holes)

ScalerFab's RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper for Element RC Enduro Sendero/Trailwalker

Specifications:

- 74mm wide
- 20mm deep top plate w/ some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: easier to touch up using a can of Rustoleum Truck Bed Coating, available here: https://amzn.to/3kBHM81

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

ScalerFab's RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper for Element RC Enduro Utron Trail Truck

Increase the performance and appearance of your scale RC truck with the Comp-Style Element RC Enduro Utron Trail Truck Front Bumper. The low-profile design offers a sleek and scale push bar look, while also improving overall performance.

Specifications:
REQUIRES REMOVAL OF STOCK IFS FRONT SKID
- 74mm wide
- 20mm deep top plate w/ some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Specifications:

- approx. 79mm wide (Just a bit wider than the frame rails)
- Raised approx. 20mm above the top corner of the frame rails to close body gap
- no fore/aft adjustment
- Bumper fits tight to the frame for the best possible approach angle.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Back screws with a washer and nut.

 

Specifications:

- approx. 79mm wide (Just a bit wider than the frame rails)
- no fore/aft adjustment
- Bumper fits tight to the frame for the best possible approach angle.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

Specifications:

- Finished width 79mm wide (74mm standard scx10 bracket width)
- 20mm deep top plate w/ approx. 12mm of fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Can be drilled to accept winch.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Fits the following bodies, and may fit others (bumper sits even with top of frame rails and offers some fore/aft adjustment):

-Jeep Wrangler
-Pro-Line SR5 (with the stock plastic bumper)
-Pro-Line Jeep Wrangler
-G6/Deadbolt
-CRC Jeep Wrangler Unlimited
-Pro-Line Racing 46 Power Wagon

With over 50 possible combinations to choose from on this bumper, you can truly build the perfect piece of trail armor for your needs. If you weren't a competitor already, our Comp-Style Front Bumper w/ Trail Bar will allow you to push the limits of your SCX10/SCX10 2 without having to worry about approach angles.

Drive OVER the rocks, don't work around your bumper!

Specifications:

- Finished width 79mm wide (74mm standard scx10 bracket width)
- 20mm deep top plate w/ approx. 12mm of fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

* Steel construction - Hand Made/Welded.

* Can be drilled to accept winch.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.