Axial Adventure SCX10 III Jeep CJ-7    Low-Profile Comp Style Front Bumper  NEW RELEASE

Expertly crafted metal comp style front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Built with mild steel for a realistic scale appearance and unbeatable performance. Provides the highest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance while still protecting your rig.

- Approximately 70mm wide.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment.

Mounting Instructions:

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown.

3. Back screws with a washer and nut.

View of ScalerFab's Jeep CJ-7 Clipless Body Mount Bracket

ScalerFab Rear Bumper for Axial SCX10 III Jeep CJ-7

Experience the ultimate in scale appearance with our Rear Bumper for the Axial Adventures SCX10 III Jeep CJ-7. Made from mild steel, this bumper not only looks like the real thing, but also offers added durability and protection for your RC vehicle. Customize your bumper even further with optional add-ons like the tire carrier. Upgrade your RC experience today!

ScalerFab Welded Steel Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7 Trail Bar & Stinger options available. **NEW option for Clipless Body Mount Bracket.

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle while still allowing for a bumper-mounted winch. 

- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and 8274 Winch, 3Racing Winch, and SSD Ox Power Winch mounting pattern)
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment

TO MOUNT WINCH: You will need to flip the winch mounting plate in order to install on bumper.

   

ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7 Trail Bar & Stinger options available. **NEW option for Clipless Body Mount Bracket.

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.

ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10 III Jeep CJ-7 Trail Bar & Stinger options available. ** NEW OPTION - CLIPLESS BODY MOUNT BRACKET

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.

ScalerFab Welded Steel Narrow Front Bumper for Element RC Enduro Utron Trail Truck

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: 
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

ScalerFab Welded Steel Narrow Winch Front Bumper for Element RC Enduro Utron Trail Truck

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: 
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: 

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

ScalerFab Welded Steel Prerunner Series Rear Bumper for Element RC Enduro Utron Trail Truck

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions:
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Full-size Steel, welded front bumper for the Element Eduro Utron Trail Truck

Upgrade your Element RC Utron Trail Truck with this full-size scale bumper. Not only does it add a rugged, scale look, but it's also built tough and ready to enhance your truck's performance. Up your scale game with the Enduro Utron Trail Truck full-width front bumper!

Specifications:
*Pictures depict optional add-ons
-175mm wide
-requires removal of the stock IFS skid plate
-Bumper is not made to fit a bumper-mounted winch. This model is built to give the best approach angle possible for this full-size option. Shown with optional front fairlead mount for servo winch.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 217mm wide
- Mounts using existing holes in frame. Does not mount like stock plastic bumper(s) - Longer Hardware recommended (hardware not included)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

Mounting instructions: 
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

ScalerFab's RC Scale Welded Steel Ultra Low-Profile Comp-Style Front Bumper for Element RC Enduro Utron Trail Truck

Increase the performance and appearance of your scale RC truck with the Comp-Style Element RC Enduro Utron Trail Truck Front Bumper. The low-profile design offers a sleek and scale push bar look, while also improving overall performance.

Specifications:
REQUIRES REMOVAL OF STOCK IFS FRONT SKID
- 74mm wide
- 20mm deep top plate w/ some fore/aft adjustment.
- Bumper fits tight to the frame for the best approach angle possible.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Protect your rig and look cool doing it! This is the brand new, just-released ScalerFab Element RC Enduro Knight Runner Roll Bar. Simple, yet strong and full of SCALE! 

ScalerFab Element RC Enduro Knightrunner Roll Bar

Specifications:
-Hand-welded steel 3/16 rod
-Approx. 60mm tall x 180mm wide at base
-Does not mount with the stock bed rack system. Removal of rack and rails required for installation.
-Mounts using 2 holes on wheel wells and drilling 2 additional holes in the front of the truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.) Misc. hardware can be purchased HERE.

Choose your own adventure with the ScalerFab Comp-style front bumper for Axial Adventure SCX10 Pro 4WD Chassis. Built with carbon steel, this bumper will let you trail with confidence. Customize with our optional add-ons for your specific body.

Specifications:

- Approx. 82mm wide bumper with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. 
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Protect your rig and look cool doing it! Simple, yet strong and full of SCALE! 

ScalerFab Roll Bar for Traxxas TRx4 1970 Series Trucks

Specifications:
-Hand-welded steel 3/16 rod
-Mounts using 2 holes on wheel wells and drilling 2 additional holes in the front of the truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.) Misc. hardware can be purchased HERE.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: 
*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

This Axial Adventure SCX10 PRO Front Bumper with Gussets (Pro series gussets for added strangth) is the perfect addition for your SCX10 Pro chassis. Made of sturdy metal, this bumper is designed for long lasting performance, allowing you to customize your adventure bumper with optional add-ons!

Specifications:

- 115mm wide with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. **Pics depict regular scx10 bumpers. The pro WILL HAVE STRAIGHT slots for mount to the new PRO chassis.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

This Axial Adventure SCX10 PRO Front Bumper is the perfect addition for your SCX10 Pro chassis. Made of sturdy metal, this bumper is designed for long lasting performance, allowing you to customize your adventure bumper with optional add-ons!

Specifications:

- 115mm wide bumper with 80mm wide inside bracket measurement
-Straight mounting slots specifically for the Pro Chassis. This is different than the usual axial offset mounting holes. **Pics depict regular scx10 bumpers. The pro WILL HAVE STRAIGHT slots for mount to the new PRO chassis.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) - see photos (Longer hardware recommended- hardware not included)
- Steel construction - Hand Made/Welded.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and SSD Ox Power Winch mounting pattern)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Flat Black: Matte black finish.

-Raw Steel: We recommend a raw steel finish if you intend to coat with a harder finish on your own.

 Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:

- approx. 150mm wide
- Trimming of body straight will provide a better fit
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

Mounting instructions:

- Bumper mounts against the frame rails, sandwiched between frame rails and plastic inner fenders. 
-Extended mounting rod included. Body pin should be inserted from the bottom with the long end sticking up through the slot on the plastic mount to keep it in place. 
-For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Specifications:

- 78mm wide (74mm inside to inside bracket measurement)
- Includes 3/8 rod extended mounting rod with predrilled hole for normal stock body mounting with bumper.
- Steel construction - Hand Made/Welded.

Mounting instructions:

- Bumper mounts against the frame rails, sandwiched between frame rails and plastic inner fenders. 
-Extended mounting rod included. Body pin should be inserted from the bottom with the long end sticking up through the slot on the plastic mount to keep it in place. 
-For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: matte black finish, susceptible to scratches under normal use.

Specifications:

- 78mm wide (74mm inside to inside bracket measurement)
- Includes 3/8 rod extended mounting rod with predrilled hole for normal stock body mounting with bumper.
- Steel construction - Hand Made/Welded.

Mounting instructions:

- Bumper mounts against the frame rails, sandwiched between frame rails and plastic inner fenders. 
-Extended mounting rod included. Body pin should be inserted from the bottom with the long end sticking up through the slot on the plastic mount to keep it in place. 
-For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: matte black finish, susceptible to scratches under normal use.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 76mm wide
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 76mm wide
- Includes predrilled top plate for mounting winch (RC4WD 9.5cti winch pattern)
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 76mm wide
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 76mm wide
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
- Steel construction - Hand Made/Welded.
- Has slots for adjustable fore/aft mounting

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

ScalerFab Welded Steel Rear Bumper for the Vanquish VS4-10 Phoenix

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

 -Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own.

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Protect your rig and look cool doing it! This is the brand new, just released ScalerFab Element RC Enduro Sendero Roll Bar. Simple, yet strong and full of SCALE! 

ScalerFab Axial Adventure SCX10 III Base Camp Roll Bar

Specifications:
-Hand-welded steel 3/16 rod
-Approx. 50mm tall x 185mm wide
-Angled slightly towards body to close body gap.
-Mounts by drilling 4 holes into truck bed, hardware not included. (*Requires four (4) 3mm x 8mm screws w/ nuts.)

Specifications:
-195mm wide, raised approx. 20mm above top of frame rails to close body gap.
- Predrilled with mounting holes to fit the RC4WD 9.5 CTI hole pattern. *Bumper is made to allow for a bumper-mounted winch behind the grill/body, not in front.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

Specifications:

- approx. 79mm wide (Just a bit wider than the frame rails)
- Raised approx. 20mm above the top corner of the frame rails to close body gap
- no fore/aft adjustment
- Bumper fits tight to the frame for the best possible approach angle.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Back screws with a washer and nut.

 

ScalerFab Full-Width Welded Steel Rear Bumper for the Axial SCX10III Base Camp

Add a little scale to your RC! This classic style bumper offers a series of customized options. Add a license plate recess or hitch receiver for an ultra scale appearance.

 Specifications:

Element RC Enduro Knightrunner Rock Sliders w/ Skid Plates
Steel Frame-mounted Rock Sliders w/ Skid Plates for mounting electronics, etc
The receiver box and ESC will either need to be relocated or attached to our skid plates option, which we highly recommend.

ALL NEW Body Capture Bar Option available! Our Body Capture Bar supports the lexan body for full protection to help keep the body from caving in or tearing! (All pictures depict this option- a solid rod behind the main Rock Slider Bar with enough space for the body to fit between the two)

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: Superficial coating - chips easily, but is easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: Superficial coating - chips easily, but is easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

-Rustoleum Truck Bed Coating: Superficial coating - chips easily, but is easier to touch up using a can of Rustoleum Truck Bed Coating, available here: HERE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
- 200mm wide
- Mounts using existing holes in frame. Does not mount like stock plastic bumper(s) - Longer Hardware recommended (hardware not included)
- Steel construction - Hand Made/Welded.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below: