SCX10/ SCX10 2 Rock Sliders For UMG10 Unimog
Steel Frame-mounted Rock Sliders w/ Optional Add-Ons (Shown in pictures)

**Note - these sliders mount directly to the frame rails and take the place of the stock skid. We highly recommend the skid plates option on our sliders for performance and in order to mount electronics.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Specifications:
- 195mm wide including wrapped edges
- Will not fit a bumper-mounted winch (this rig is specifically built for a servo winch)
- Steel construction - Hand Made/Welded.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
***NOTE: Bumper brackets mount between frame and Front Body Post Receiver. - Body posts will need to be spread slightly to mount properly. Also, we recommend using a smaller body clip, as the stock ones will not completely clip due to bracket interference. Alternately, new holes could be drilled in the body posts perpendicular to the stock ones to allow the body clips to be pushed in from the front or back with no interference vs the side.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-190mm wide
- Will not fit a bumper-mounted winch (this rig is specifically built for a servo winch)
- Steel construction - Hand Made/Welded.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
***NOTE: Bumper brackets mount between frame and Front Body Post Receiver. - Body posts will need to be spread slightly to mount properly. Also, we recommend using a smaller body clip, as the stock ones will not completely clip due to bracket interference. Alternately, new holes could be drilled in the body posts perpendicular to the stock ones to allow the body clips to be pushed in from the front or back with no interference vs the side.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Specifications:
-190mm wide
- Will not fit a bumper-mounted winch (this rig is specifically built for a servo winch)
- Steel construction - Hand Made/Welded.
- Mounts using existing holes in frame - does not mount like stock plastic bumper(s) (Longer hardware recommended- hardware not included- See Optional Bumper Hardware Pack available under Accessories)
***NOTE: Bumper brackets mount between frame and Front Body Post Receiver. - Body posts will need to be spread slightly to mount properly. Also, we recommend using a smaller body clip, as the stock ones will not completely clip due to bracket interference. Alternately, new holes could be drilled in the body posts perpendicular to the stock ones to allow the body clips to be pushed in from the front or back with no interference vs the side.

**Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: Superficial matte black coating, will scratch under normal use.

-Rustoleum Truck Bed Coating: OUT OF STOCK/NO LONGER AVAILABLE

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight.

*Recommend hardware mounting kits available at the top of the page as an optional add-on.**

Mounting instructions: We recommend removing any plastic cross-members and screwing directly into the frame rails with a nut on the back. For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. Recommend hardware mounting kits HERE or at the top of the page as an optional add-on.** Links to additional recommended extras can be found HERE.

Main pic courtesty of #westernparccrawlers on IG! #ScalerFab for a feature!